Продукция

Расходомер жидкостной турбины ADDA-FL-WL

Артикул ADDA-FL-WL Рубрика

Расходомер жидкостной турбины ADDA-FL-WL

Расходомер жидкостной турбины для чистых жидкостей с низкой вязкостью. доступны варианты DN4 (DN300) с резьбовыми, фланцевыми, пластинчатыми или санитарно-зажимными соединениями. выберите электронику GA без локального дисплея или электронику GN со встроенным ЖК-дисплеем, с вариантами вывода, подходящими для системы управления.

Авторитетные квалификационные сертификаты

Мы имеем сертификацию качества ISO, национальную квалификацию высокотехнологичного предприятия, одобрение типа измерительного прибора в Китае, а также взрывозащищенные сертификаты и сертификаты безопасности для поддержки надежного качества продукции.

Инженерное дело на заказ

Настраиваемые материалы, соединения, сигналы, дисплеи и решения для установки для различных технологических сред.

Обзор | Спецификации | Диапазоны потоков | Размеры | Установка

Обзор

The ADDA-FL-WL is a velocity-type turbine flow meter for clean, low-viscosity liquids that are not strongly corrosive. Liquid passing through the meter drives a rotor; its speed is converted into an electrical signal proportional to flow. The series is used in food and pharmaceutical processing, fine chemicals, petroleum and other liquid measurement applications.

Select the wetted materials, process connection and electronics to suit the liquid, operating pressure, temperature and required flow range.

Особенности

  • Nominal sizes from DN4 to DN300, depending on connection type.
  • GA versions without local display and GN versions with an integral LCD.
  • Pulse, 4–20 mA, Modbus RTU over RS485 and HART options, depending on electronics.
  • GN versions display volumetric flow and can calculate mass flow from a configured liquid density.
  • Threaded, flanged, wafer and sanitary clamp connection options.

Принцип работы

The flowing liquid applies torque to the angled turbine blades. Within the calibrated operating range, rotor speed is proportional to average liquid velocity. A magnetic pickup detects the rotating blades and generates pulses; the electronics process these pulses to indicate instantaneous flow and totalized volume.

Q = 3.6 × f / K, where Q is volumetric flow at operating conditions in m³/h, f is pulse frequency in Hz, and K is the meter factor in pulses per litre. Use the meter factor stated in the individual calibration report.

Turbine rotor, electromagnetic conversion, pulse calculation and output diagram
Turbine flow measurement principle

Технические характеристики

ПараметрСпецификация
МодельADDA-FL-WL
Suitable liquidsClean liquids without solid impurities; kinematic viscosity below 10 mm²/s; not strongly corrosive
Meter body304 or 316 stainless steel
Rotor materials, DN4–DN1252Cr13 stainless steel or 2205 duplex stainless steel
Rotor materials, DN150–DN300304 hub with 430 blades, or 316 hub with 2205 duplex stainless steel blades
Process temperature−40 to +120°C or −40 to +150°C, depending on version; −40 to +80°C option also listed in the ordering guide
Температура окружающей среды−20 to +60°C
Relative humidity5–95%
Рейтинг давленияPN10–PN400 or Class 150–2500, depending on nominal size and connection
Accuracy optionsVersion-dependent; see electronics table below. Class 0.2 is available on request.
Referenced product standardJB/T 9246-2016, Turbine Flow Sensors
Referenced verification regulationJJG 1037-2008, Turbine Flowmeters
Параметры подключения процесса
ConnectionAvailable nominal sizes
External threadDN4–DN80
Internal threadDN4–DN50
FlangedDN4 — DN300
WaferDN15 DN200 DN15
Sanitary clampDN4–DN100

Electronics Versions

ПараметрGA without local displayGN with integral LCD
FunctionRemote transmission for flow computers, PLCs and control systemsLocal indication and remote signal transmission
Accuracy classes2.5, 1.5, 1.0 or 0.50.5, 0.3 or 0.2; class 0.2 on request
ПовторяемостьBetter than 0.15%Better than 0.15%
Питание24 V DC nominal; 5–32 V DC or 16–32 V DC depending on output24 V DC
Параметры выводаPulse or 4–20 mAPulse or two-wire 4–20 mA; HART and Modbus RTU over RS485 configurations available
Electrical connectionsCircular plug, cable lead or Hirschmann-type connectorМ20 × 1,5 или 1/2 ДНЯО
Защита входаIP65 or IP67, depending on versionIP67

Output, power-supply and protection options must be selected as a compatible configuration. Hazardous-area versions are available on request; confirm the marking and applicable certification for the supplied unit.

Liquid Flow Ranges

Номинальный размерFlow range (m³/h)
ДН40.04–0.4
ДН60.06–0.6
ДН100.15–1.5
ДН150.5–6
ДН200.45–9
ДН250.5–10
ДН320.8–15
ДН401–20
ДН502–40
ДН655–70
ДН807–100
ДН10010–200
ДН12513–250
ДН15015–300
ДН20040–800
ДН250100–1000
ДН300120–1200

Select a size so that the normal operating flow is preferably within 20–80% of the selected meter’s maximum flow. Confirm suitability against liquid properties and process conditions.

Pressure Rating Options

Pressure Rating Options — Part 1 of 3
РазмерExternal thread PNInternal thread PNФланцевый ПН
ДН416–6316–6316–63
ДН616–6316–6316–63
ДН1016–6316–6316–63
ДН1516–6316–6316–250
ДН2016–6316–6316–250
ДН2516–6316–6316–250
ДН3216–6316–6316–250
ДН4016–6316–6316–250
ДН5016–6316–6316–250
ДН6516–63—16–250
ДН8016–63—16–250
ДН100——16–250
ДН125——16–250
ДН150——16–250
ДН200——16–250
ДН250——16–40
ДН300——16–40
Pressure Rating Options — Part 2 of 3
РазмерФланцевый классWafer PNWafer Class
ДН4———
ДН6———
ДН10———
ДН15150–150063–400150–2500
ДН20150–150063–400150–2500
ДН25150–150063–400150–2500
ДН32150–150063–400150–2500
ДН40150–150063–400150–2500
ДН50150–150063–400150–2500
ДН65150–150063–400150–2500
ДН80150–60063–400150–2500
ДН100150–60063–400150–2500
ДН125150–60063–400150–2500
ДН150150–60063–400150–2500
ДН200150–30063–400150–2500
ДН250150–300——
ДН300150——
Pressure Rating Options — Part 3 of 3
РазмерЗажим PN
ДН410
ДН610
ДН1010
ДН1510
ДН2010
ДН2510
ДН3210
ДН4010
ДН5010
ДН6510
ДН8010
ДН10010
ДН125—
ДН150—
ДН200—
ДН250—
ДН300—

PN and Class are separate rating systems. Available ratings depend on the connection and size. Entries marked “—” are not specified here; confirm on request.

Selection Options

SelectionКодОпция
ElectronicsGAWithout local display
ElectronicsГНIntegral LCD
ConnectionF1Flanged
ConnectionF2Wafer
ConnectionF3Sanitary clamp
ConnectionL1External thread
ConnectionL2Internal thread
Body material4304 нержавеющая сталь
Body material6316 stainless steel
Rotor material2C2Cr13 stainless steel
Rotor material252205 duplex stainless steel
OutputGA124 V DC, no local display, 4–20 mA
OutputGA224 V DC, no local display, pulse
OutputGN124 V DC, local display, pulse
OutputGN224 V DC, local display, 4–20 mA
OutputGN324 V DC, local display, 4–20 mA + HART
OutputGN424 V DC, local display, Modbus RTU over RS485
Temperature1−40 to +80°C
Temperature2−40 to +120°C
Temperature3−40 to +150°C
Hazardous-area requirementNNon-explosion-protected version
Hazardous-area requirementDFlameproof version; confirm marking and certification for the selected configuration

State the required nominal size, pressure rating, accuracy class, electrical connection and transmitter appearance when ordering. The final configuration must be confirmed for the application.

Размеры

Dimensions are in millimetres unless otherwise stated. Use the dimensional drawing and table for the selected connection and pressure rating.

External Thread Connection

ADDA-FL-WL turbine flow meter side-view dimensional drawing with threaded ends
External-thread connection, DN4–DN10, with straight pipe sections
ADDA-FL-WL threaded turbine flow meter side and end dimensions
External-thread connection, DN15–DN80

DN4–DN10 external-thread versions include straight pipe sections. DN15–DN80 versions do not include straight pipe sections.

РазмерРейтинг давленияL (mm)G male threadb (mm)
ДН4PN63 or lower296Г1/213
ДН6PN63 or lower296Г1/213
ДН10PN63 or lower413Г1/213
ДН15PN63 or lower75Г115
ДН20PN63 or lower85Г115
ДН25PN63 or lower100G1-1/415
ДН32PN63 or lower140Г220
ДН40PN63 or lower140Г220
ДН50PN63 or lower150G2-1/230
ДН65PN63 or lower170G335
ДН80PN63 or lower200G440

Internal Thread Connection

ADDA-FL-WL flanged turbine flow meter side-view dimensional drawing
Internal-thread connection, DN4–DN50
РазмерРейтинг давленияL (mm)G female threadD (mm)
ДН4PN63 or lower75G3/842
ДН6PN63 or lower75G3/842
ДН10PN63 or lower75Г1/242
ДН15PN63 or lower100Г1/244
ДН20PN63 or lower120Г3/443
ДН25PN63 or lower120Г149
ДН32PN63 or lower120G1-1/456
ДН40PN63 or lower120G1-1/260
ДН50PN63 or lower120Г272

Flanged Connection

ADDA-FL-WL turbine flow meter side and end dimensional views
Small-bore flanged connection with straight pipe sections
ADDA-FL-WL flange bolt pattern and transmitter dimensional views
Flanged connection dimensions
PN flange dimensions — Part 1 of 2
РазмерРейтинг давленияL (mm)D (mm)
ДН4PN40 or lower29695
ДН6PN40 or lower29695
ДН10PN40 or lower41395
ДН15PN40 or lower7595
ДН20PN40 or lower85105
ДН25PN40 or lower100115
ДН32PN40 or lower140140
ДН40PN40 or lower140150
ДН50PN40 or lower150165
ДН65PN16170185
ДН80PN16200200
ДН100PN16220220
ДН125PN16250250
ДН150PN16300285
ДН200PN16350340
ДН250PN16400405
ДН300PN16350460
PN flange dimensions — Part 2 of 2
РазмерK (mm)d (mm)n holes
ДН465144
ДН665144
ДН1065144
ДН1565144
ДН2075144
ДН2585144
ДН32100184
ДН40110184
ДН50125184
ДН65145188
ДН80160188
ДН100180188
ДН125210188
ДН150240228
ДН2002952212
ДН2503552612
ДН3004102612
Class 150 flange dimensions — Part 1 of 2
РазмерPressure classL (mm)D (mm)
ДН4Class15029690
ДН6Class15029690
ДН10Class15041390
ДН15Class1507590
ДН20Class15085100
ДН25Class150100110
ДН32Class150140115
ДН40Class150140125
ДН50Class150150150
ДН65Class150170180
ДН80Class150200190
ДН100Class150220230
ДН125Class150250255
ДН150Class150300280
ДН200Class150350345
ДН250Class150400405
ДН300Class150350485
Class 150 flange dimensions — Part 2 of 2
РазмерK (mm)d (mm)n holes
ДН460.3164
ДН660.3164
ДН1060.3164
ДН1560.3164
ДН2069.9164
ДН2579.4164
ДН3288.9164
ДН4098.4164
ДН50120.7184
ДН65139.7184
ДН80152.4184
ДН100190.5188
ДН125215.9228
ДН150241.3228
ДН200298.5228
ДН2503622612
ДН300431.82612

Wafer Connection

ADDA-FL-WL flanged turbine flow meter side and front dimensions
Wafer connection dimensions
РазмерРейтинг давленияL (mm)D (mm)
ДН15PN400 or lower6553
ДН20PN400 or lower6053
ДН25PN400 or lower6058
ДН32PN400 or lower7066
ДН40PN400 or lower7072
ДН50PN400 or lower7092
ДН65PN400 or lower80100
ДН80PN400 or lower90112
ДН100PN400 or lower100137
ДН125PN400 or lower120165
ДН150PN400 or lower150190
ДН200PN400 or lower150242

The catalogue gives the same wafer body dimensions across the available pressure ratings. When supplied with mating weld-neck flanges, total length equals the standard body length plus twice the mating-flange thickness.

Sanitary Clamp Connection

ADDA-FL-WL compact turbine flow meter body and transmitter dimensions
Sanitary clamp connection dimensions
ADDA-FL-WL turbine flow meter transmitter and flange front view
Sanitary clamp connection end view
Sanitary Clamp Connection — Part 1 of 2
РазмерРейтинг давленияL (mm)D (mm)
ДН4PN105050.5
ДН6PN105050.5
ДН10PN105050.5
ДН15PN1010050.5
ДН20PN1010050.5
ДН25PN1010050.5
ДН32PN1012050.5
ДН40PN1014064
ДН50PN1015077.5
ДН65PN1017091
ДН80PN10200106
ДН100PN10220130
Sanitary Clamp Connection — Part 2 of 2
Размерd (mm)C (mm)
ДН4443.5
ДН6643.5
ДН101043.5
ДН151543.5
ДН202043.5
ДН252543.5
ДН323243.5
ДН404056.5
ДН505070.5
ДН656583.5
ДН808097
ДН100100122

Installation Requirements

RequirementGuidance
Straight pipe after reducers, expanders or elbowsProvide at least 15D upstream and 5D downstream. D is the nominal internal diameter of the flow meter.
Pipe alignmentAlign the meter and pipeline concentrically before installation.
CleanlinessFlush new pipework before fitting the meter to remove welding debris and other foreign material.
Process connectionsUse the mating fittings, gaskets, fasteners and sealing method appropriate to the selected thread, flange, wafer or clamp connection.

Связанные продукты

Витрина дела

Часто задаваемые вопросы

Найдите быстрые ответы о выборе продукта, настройке, технических параметрах, доставке и поддержке промышленных измерительных приборов ADDA.

官询盘

Пожалуйста, укажите измеряемую среду, диапазон измерения, температуру процесса, технологическое давление, тип соединения, выходной сигнал, источник питания, среду установки и метод связи, если требуется удаленный мониторинг.

Да. ADDA может предоставить индивидуальные решения, основанные на диапазоне измерения, технологическом соединении, смоченном материале, типе отображения, протоколе связи, методе установки и рабочей среде.

Многие приборы ADDA доступны со взрывозащищенными или искробезопасными конфигурациями. пожалуйста, подтвердите требования классификации и сертификации объекта перед выбором.

Да. Наша команда может помочь рекомендовать подходящую конфигурацию прибора после рассмотрения условий применения, включая требования к среде, дальности, подключению, выходному сигналу и установке.

Время выполнения зависит от типа продукта, количества, требований к настройке, и потребности сертификации Стандартные продукты обычно имеют более короткий срок поставки, в то время как индивидуальные модели могут потребовать дополнительного времени производства.

Свяжитесь с нами для сотрудничества

官询盘