제품

ADDA-FL-WL Liquid Turbine Flow Meter

SKU ADDA-FL-WL 카테고리

ADDA-FL-WL Liquid Turbine Flow Meter

깨끗하고 점도가 낮은 액체를 위한 액체 터빈 유량계. DN4–DN300 옵션은 나사형,플랜지형, 웨이퍼 또는 위생 클램프 연결과 함께 사용할 수 있습니다. 로컬 디스플레이가 없는 GA 전자 장치 또는 일체형 LCD 가 있는 GN 전자 장치를 선택하고 제어 시스템에 맞는 출력 옵션을 제공합니다.

권위있는 자격 인증

우리는 ISO 품질 인증, 국가 하이테크 기업 자격, 중국 측정 기기 형식 승인, 폭발 방지 및 안전 인증을 보유하여 신뢰할 수있는 제품 품질을 지원합니다.

맞춤형 엔지니어링

다양한 공정 환경을 위한 구성 가능한 재료, 연결, 신호, 디스플레이 및 설치 솔루션.

Overview | Specifications | Flow Ranges | Dimensions | Installation

Overview

The ADDA-FL-WL is a velocity-type turbine flow meter for clean, low-viscosity liquids that are not strongly corrosive. Liquid passing through the meter drives a rotor; its speed is converted into an electrical signal proportional to flow. The series is used in food and pharmaceutical processing, fine chemicals, petroleum and other liquid measurement applications.

Select the wetted materials, process connection and electronics to suit the liquid, operating pressure, temperature and required flow range.

Features

  • Nominal sizes from DN4 to DN300, depending on connection type.
  • GA versions without local display and GN versions with an integral LCD.
  • Pulse, 4–20 mA, Modbus RTU over RS485 and HART options, depending on electronics.
  • GN versions display volumetric flow and can calculate mass flow from a configured liquid density.
  • Threaded, flanged, wafer and sanitary clamp connection options.

Operating Principle

The flowing liquid applies torque to the angled turbine blades. Within the calibrated operating range, rotor speed is proportional to average liquid velocity. A magnetic pickup detects the rotating blades and generates pulses; the electronics process these pulses to indicate instantaneous flow and totalized volume.

Q = 3.6 × f / K, where Q is volumetric flow at operating conditions in m³/h, f is pulse frequency in Hz, and K is the meter factor in pulses per litre. Use the meter factor stated in the individual calibration report.

Turbine rotor, electromagnetic conversion, pulse calculation and output diagram
Turbine flow measurement principle

기술 사양

ParameterSpecification
ModelADDA-FL-WL
Suitable liquidsClean liquids without solid impurities; kinematic viscosity below 10 mm²/s; not strongly corrosive
Meter body304 or 316 stainless steel
Rotor materials, DN4–DN1252Cr13 stainless steel or 2205 duplex stainless steel
Rotor materials, DN150–DN300304 hub with 430 blades, or 316 hub with 2205 duplex stainless steel blades
Process temperature−40 to +120°C or −40 to +150°C, depending on version; −40 to +80°C option also listed in the ordering guide
Ambient temperature−20 to +60°C
Relative humidity5–95%
Pressure ratingPN10–PN400 or Class 150–2500, depending on nominal size and connection
Accuracy optionsVersion-dependent; see electronics table below. Class 0.2 is available on request.
Referenced product standardJB/T 9246-2016, Turbine Flow Sensors
Referenced verification regulationJJG 1037-2008, Turbine Flowmeters
Process connection options
ConnectionAvailable nominal sizes
External threadDN4–DN80
Internal threadDN4–DN50
FlangedDN4–DN300
WaferDN15–DN200
Sanitary clampDN4–DN100

Electronics Versions

ParameterGA without local displayGN with integral LCD
FunctionRemote transmission for flow computers, PLCs and control systemsLocal indication and remote signal transmission
Accuracy classes2.5, 1.5, 1.0 or 0.50.5, 0.3 or 0.2; class 0.2 on request
RepeatabilityBetter than 0.15%Better than 0.15%
Power supply24 V DC nominal; 5–32 V DC or 16–32 V DC depending on output24 V DC
Output optionsPulse or 4–20 mAPulse or two-wire 4–20 mA; HART and Modbus RTU over RS485 configurations available
Electrical connectionsCircular plug, cable lead or Hirschmann-type connectorM20 × 1.5 or 1/2 NPT
Ingress protectionIP65 or IP67, depending on versionIP67

Output, power-supply and protection options must be selected as a compatible configuration. Hazardous-area versions are available on request; confirm the marking and applicable certification for the supplied unit.

Liquid Flow Ranges

Nominal sizeFlow range (m³/h)
DN40.04–0.4
DN60.06–0.6
DN100.15–1.5
DN150.5–6
DN200.45–9
DN250.5–10
DN320.8–15
DN401–20
DN502–40
DN655–70
DN807–100
DN10010–200
DN12513–250
DN15015–300
DN20040–800
DN250100–1000
DN300120–1200

Select a size so that the normal operating flow is preferably within 20–80% of the selected meter’s maximum flow. Confirm suitability against liquid properties and process conditions.

Pressure Rating Options

Pressure Rating Options — Part 1 of 3
SizeExternal thread PNInternal thread PNFlanged PN
DN416–6316–6316–63
DN616–6316–6316–63
DN1016–6316–6316–63
DN1516–6316–6316–250
DN2016–6316–6316–250
DN2516–6316–6316–250
DN3216–6316–6316–250
DN4016–6316–6316–250
DN5016–6316–6316–250
DN6516–63—16–250
DN8016–63—16–250
DN100——16–250
DN125——16–250
DN150——16–250
DN200——16–250
DN250——16–40
DN300——16–40
Pressure Rating Options — Part 2 of 3
SizeFlanged ClassWafer PNWafer Class
DN4———
DN6———
DN10———
DN15150–150063–400150–2500
DN20150–150063–400150–2500
DN25150–150063–400150–2500
DN32150–150063–400150–2500
DN40150–150063–400150–2500
DN50150–150063–400150–2500
DN65150–150063–400150–2500
DN80150–60063–400150–2500
DN100150–60063–400150–2500
DN125150–60063–400150–2500
DN150150–60063–400150–2500
DN200150–30063–400150–2500
DN250150–300——
DN300150——
Pressure Rating Options — Part 3 of 3
SizeClamp PN
DN410
DN610
DN1010
DN1510
DN2010
DN2510
DN3210
DN4010
DN5010
DN6510
DN8010
DN10010
DN125—
DN150—
DN200—
DN250—
DN300—

PN and Class are separate rating systems. Available ratings depend on the connection and size. Entries marked “—” are not specified here; confirm on request.

Selection Options

Selection코드옵션
ElectronicsGAWithout local display
ElectronicsGNIntegral LCD
ConnectionF1Flanged
ConnectionF2Wafer
ConnectionF3Sanitary clamp
ConnectionL1External thread
ConnectionL2Internal thread
Body material4304 stainless steel
Body material6316 stainless steel
Rotor material2C2Cr13 stainless steel
Rotor material252205 duplex stainless steel
OutputGA124 V DC, no local display, 4–20 mA
OutputGA224 V DC, no local display, pulse
OutputGN124 V DC, local display, pulse
OutputGN224 V DC, local display, 4–20 mA
OutputGN324 V DC, local display, 4–20 mA + HART
OutputGN424 V DC, local display, Modbus RTU over RS485
Temperature1−40 to +80°C
Temperature2−40 to +120°C
Temperature3−40 to +150°C
Hazardous-area requirementNNon-explosion-protected version
Hazardous-area requirementDFlameproof version; confirm marking and certification for the selected configuration

State the required nominal size, pressure rating, accuracy class, electrical connection and transmitter appearance when ordering. The final configuration must be confirmed for the application.

Dimensions

Dimensions are in millimetres unless otherwise stated. Use the dimensional drawing and table for the selected connection and pressure rating.

External Thread Connection

ADDA-FL-WL turbine flow meter side-view dimensional drawing with threaded ends
External-thread connection, DN4–DN10, with straight pipe sections
ADDA-FL-WL threaded turbine flow meter side and end dimensions
External-thread connection, DN15–DN80

DN4–DN10 external-thread versions include straight pipe sections. DN15–DN80 versions do not include straight pipe sections.

SizePressure ratingL (mm)G male threadb (mm)
DN4PN63 or lower296G1/213
DN6PN63 or lower296G1/213
DN10PN63 or lower413G1/213
DN15PN63 or lower75G115
DN20PN63 or lower85G115
DN25PN63 or lower100G1-1/415
DN32PN63 or lower140G220
DN40PN63 or lower140G220
DN50PN63 or lower150G2-1/230
DN65PN63 or lower170G335
DN80PN63 or lower200G440

Internal Thread Connection

ADDA-FL-WL flanged turbine flow meter side-view dimensional drawing
Internal-thread connection, DN4–DN50
SizePressure ratingL (mm)G female threadD (mm)
DN4PN63 or lower75G3/842
DN6PN63 or lower75G3/842
DN10PN63 or lower75G1/242
DN15PN63 or lower100G1/244
DN20PN63 or lower120G3/443
DN25PN63 or lower120G149
DN32PN63 or lower120G1-1/456
DN40PN63 or lower120G1-1/260
DN50PN63 or lower120G272

Flanged Connection

ADDA-FL-WL turbine flow meter side and end dimensional views
Small-bore flanged connection with straight pipe sections
ADDA-FL-WL flange bolt pattern and transmitter dimensional views
Flanged connection dimensions
PN flange dimensions — Part 1 of 2
SizePressure ratingL (mm)D (mm)
DN4PN40 or lower29695
DN6PN40 or lower29695
DN10PN40 or lower41395
DN15PN40 or lower7595
DN20PN40 or lower85105
DN25PN40 or lower100115
DN32PN40 or lower140140
DN40PN40 or lower140150
DN50PN40 or lower150165
DN65PN16170185
DN80PN16200200
DN100PN16220220
DN125PN16250250
DN150PN16300285
DN200PN16350340
DN250PN16400405
DN300PN16350460
PN flange dimensions — Part 2 of 2
SizeK (mm)d (mm)n holes
DN465144
DN665144
DN1065144
DN1565144
DN2075144
DN2585144
DN32100184
DN40110184
DN50125184
DN65145188
DN80160188
DN100180188
DN125210188
DN150240228
DN2002952212
DN2503552612
DN3004102612
Class 150 flange dimensions — Part 1 of 2
SizePressure classL (mm)D (mm)
DN4Class15029690
DN6Class15029690
DN10Class15041390
DN15Class1507590
DN20Class15085100
DN25Class150100110
DN32Class150140115
DN40Class150140125
DN50Class150150150
DN65Class150170180
DN80Class150200190
DN100Class150220230
DN125Class150250255
DN150Class150300280
DN200Class150350345
DN250Class150400405
DN300Class150350485
Class 150 flange dimensions — Part 2 of 2
SizeK (mm)d (mm)n holes
DN460.3164
DN660.3164
DN1060.3164
DN1560.3164
DN2069.9164
DN2579.4164
DN3288.9164
DN4098.4164
DN50120.7184
DN65139.7184
DN80152.4184
DN100190.5188
DN125215.9228
DN150241.3228
DN200298.5228
DN2503622612
DN300431.82612

Wafer Connection

ADDA-FL-WL flanged turbine flow meter side and front dimensions
Wafer connection dimensions
SizePressure ratingL (mm)D (mm)
DN15PN400 or lower6553
DN20PN400 or lower6053
DN25PN400 or lower6058
DN32PN400 or lower7066
DN40PN400 or lower7072
DN50PN400 or lower7092
DN65PN400 or lower80100
DN80PN400 or lower90112
DN100PN400 or lower100137
DN125PN400 or lower120165
DN150PN400 or lower150190
DN200PN400 or lower150242

The catalogue gives the same wafer body dimensions across the available pressure ratings. When supplied with mating weld-neck flanges, total length equals the standard body length plus twice the mating-flange thickness.

Sanitary Clamp Connection

ADDA-FL-WL compact turbine flow meter body and transmitter dimensions
Sanitary clamp connection dimensions
ADDA-FL-WL turbine flow meter transmitter and flange front view
Sanitary clamp connection end view
Sanitary Clamp Connection — Part 1 of 2
SizePressure ratingL (mm)D (mm)
DN4PN105050.5
DN6PN105050.5
DN10PN105050.5
DN15PN1010050.5
DN20PN1010050.5
DN25PN1010050.5
DN32PN1012050.5
DN40PN1014064
DN50PN1015077.5
DN65PN1017091
DN80PN10200106
DN100PN10220130
Sanitary Clamp Connection — Part 2 of 2
Sized (mm)C (mm)
DN4443.5
DN6643.5
DN101043.5
DN151543.5
DN202043.5
DN252543.5
DN323243.5
DN404056.5
DN505070.5
DN656583.5
DN808097
DN100100122

Installation Requirements

RequirementGuidance
Straight pipe after reducers, expanders or elbowsProvide at least 15D upstream and 5D downstream. D is the nominal internal diameter of the flow meter.
Pipe alignmentAlign the meter and pipeline concentrically before installation.
CleanlinessFlush new pipework before fitting the meter to remove welding debris and other foreign material.
Process connectionsUse the mating fittings, gaskets, fasteners and sealing method appropriate to the selected thread, flange, wafer or clamp connection.

관련 제품

케이스 쇼케이스

자주 묻는 질문

ADDA 산업용 측정 기기에 대한 제품 선택, 사용자 정의, 기술 매개변수, 납품 및 지원에 대한 빠른 답변을 찾아보세요.

官网익수

측정된 매체, 측정 범위, 공정 온도, 공정 압력, 연결 유형, 출력 신호, 전원 공급 장치, 설치 환경 및 원격 모니터링이 필요한 경우 통신 방법을 제공하십시오.

예. ADDA 는 측정 범위,공정 연결,습윤 재료,디스플레이 유형,통신 프로토콜,설치 방법 및 작업 환경을 기반으로 맞춤형 솔루션을 제공할 수 있습니다.

많은 ADDA 계측기는 방폭 또는 본질 안전 구성으로 제공됩니다. 선택하기 전에 사이트 분류 및 인증 요구 사항을 확인하십시오.

예. 저희 팀은 중간,범위, 연결,출력 신호 및 설치 요구 사항을 포함한 응용 조건을 검토한 후 적합한 기기 구성을 추천하는 데 도움을 드릴 수 있습니다.

리드타임은 제품 유형, 수량, 사용자 정의 요구 사항 및 인증 요구 사항에 따라 다릅니다. 표준 제품은 일반적으로 배송 시간이 더 짧고 사용자 정의 모델에는 추가 생산 시간이 필요할 수 있습니다.

협력을 위해 문의하세요

官网익수