उत्पादों

ADDA-FL-WL तरल टरबाइन प्रवाह मीटर

एसकेयू ADDA-FL-WL श्रेणी

ADDA-FL-WL तरल टरबाइन प्रवाह मीटर

स्वच्छ, कम-चिपचिपापन तरल पदार्थ के लिए तरल टरबाइन प्रवाह मीटर डीएन ४ एसडीएन ३०० विकल्प थ्रेडेड, फ्लैंगेड, वेफर या सैनिटरी क्लैंप कनेक्शन के साथ उपलब्ध हैं नियंत्रण प्रणाली के अनुरूप आउटपुट विकल्पों के साथ, एक अभिन्न एलसीडी के साथ स्थानीय प्रदर्शन या जीएन इलेक्ट्रॉनिक्स के बिना जीए इलेक्ट्रॉनिक्स का चयन करें।.

आधिकारिक योग्यता प्रमाणपत्र

हम आईएसओ गुणवत्ता प्रमाणन, राष्ट्रीय उच्च तकनीक उद्यम योग्यता, चीन मापने उपकरण प्रकार अनुमोदन, और विस्फोट प्रूफ और सुरक्षा प्रमाण पत्र विश्वसनीय उत्पाद की गुणवत्ता का समर्थन करने के लिए।.

कस्टम इंजीनियरिंग

विभिन्न प्रक्रिया वातावरणों के लिए कॉन्फ़िगर करने योग्य सामग्री, कनेक्शन, सिग्नल, डिस्प्ले और इंस्टॉलेशन समाधान।.

अवलोकन | निर्दिष्टीकरण | प्रवाह श्रेणियाँ | आयाम | Installation

अवलोकन

The ADDA-FL-WL is a velocity-type turbine flow meter for clean, low-viscosity liquids that are not strongly corrosive. Liquid passing through the meter drives a rotor; its speed is converted into an electrical signal proportional to flow. The series is used in food and pharmaceutical processing, fine chemicals, petroleum and other liquid measurement applications.

Select the wetted materials, process connection and electronics to suit the liquid, operating pressure, temperature and required flow range.

विशेषताएं

  • Nominal sizes from DN4 to DN300, depending on connection type.
  • GA versions without local display and GN versions with an integral LCD.
  • Pulse, 4–20 mA, Modbus RTU over RS485 and HART options, depending on electronics.
  • GN versions display volumetric flow and can calculate mass flow from a configured liquid density.
  • Threaded, flanged, wafer and sanitary clamp connection options.

ऑपरेटिंग सिद्धांत

The flowing liquid applies torque to the angled turbine blades. Within the calibrated operating range, rotor speed is proportional to average liquid velocity. A magnetic pickup detects the rotating blades and generates pulses; the electronics process these pulses to indicate instantaneous flow and totalized volume.

Q = 3.6 × f / K, where Q is volumetric flow at operating conditions in m³/h, f is pulse frequency in Hz, and K is the meter factor in pulses per litre. Use the meter factor stated in the individual calibration report.

Turbine rotor, electromagnetic conversion, pulse calculation and output diagram
Turbine flow measurement principle

तकनीकी विनिर्देश

पैरामीटरविशिष्टता
ModelADDA-FL-WL
Suitable liquidsClean liquids without solid impurities; kinematic viscosity below 10 mm²/s; not strongly corrosive
Meter body304 or 316 stainless steel
Rotor materials, DN4–DN1252Cr13 stainless steel or 2205 duplex stainless steel
Rotor materials, DN150–DN300304 hub with 430 blades, or 316 hub with 2205 duplex stainless steel blades
Process temperature−40 to +120°C or −40 to +150°C, depending on version; −40 to +80°C option also listed in the ordering guide
Ambient temperature−20 to +60°C
Relative humidity5–95%
दबाव रेटिंगPN10–PN400 or Class 150–2500, depending on nominal size and connection
Accuracy optionsVersion-dependent; see electronics table below. Class 0.2 is available on request.
Referenced product standardJB/T 9246-2016, Turbine Flow Sensors
Referenced verification regulationJJG 1037-2008, Turbine Flowmeters
प्रक्रिया कनेक्शन विकल्प
ConnectionAvailable nominal sizes
External threadDN4–DN80
Internal threadDN4–DN50
FlangedDN4–DN300
WaferDN15–DN200
Sanitary clampDN4–DN100

Electronics Versions

पैरामीटरGA without local displayGN with integral LCD
FunctionRemote transmission for flow computers, PLCs and control systemsLocal indication and remote signal transmission
Accuracy classes2.5, 1.5, 1.0 or 0.50.5, 0.3 or 0.2; class 0.2 on request
RepeatabilityBetter than 0.15%Better than 0.15%
बिजली की आपूर्ति24 V DC nominal; 5–32 V DC or 16–32 V DC depending on output24 V DC
आउटपुट विकल्पPulse or 4–20 mAPulse or two-wire 4–20 mA; HART and Modbus RTU over RS485 configurations available
Electrical connectionsCircular plug, cable lead or Hirschmann-type connectorM20 × 1.5 or 1/2 NPT
प्रवेश सुरक्षाIP65 or IP67, depending on versionआईपी67

Output, power-supply and protection options must be selected as a compatible configuration. Hazardous-area versions are available on request; confirm the marking and applicable certification for the supplied unit.

Liquid Flow Ranges

नाममात्र आकारFlow range (m³/h)
DN40.04–0.4
DN60.06–0.6
DN100.15–1.5
DN150.5–6
DN200.45–9
डीएन250.5–10
DN320.8–15
डीएन401–20
डीएन502–40
DN655–70
डीएन807–100
डीएन10010–200
DN12513–250
डीएन15015–300
डीएन20040–800
डीएन250100–1000
DN300120–1200

Select a size so that the normal operating flow is preferably within 20–80% of the selected meter’s maximum flow. Confirm suitability against liquid properties and process conditions.

Pressure Rating Options

Pressure Rating Options — Part 1 of 3
SizeExternal thread PNInternal thread PNFlanged PN
DN416–6316–6316–63
DN616–6316–6316–63
DN1016–6316–6316–63
DN1516–6316–6316–250
DN2016–6316–6316–250
डीएन2516–6316–6316–250
DN3216–6316–6316–250
डीएन4016–6316–6316–250
डीएन5016–6316–6316–250
DN6516–63—16–250
डीएन8016–63—16–250
डीएन100——16–250
DN125——16–250
डीएन150——16–250
डीएन200——16–250
डीएन250——16–40
DN300——16–40
Pressure Rating Options — Part 2 of 3
SizeFlanged ClassWafer PNWafer Class
DN4———
DN6———
DN10———
DN15150–150063–400150–2500
DN20150–150063–400150–2500
डीएन25150–150063–400150–2500
DN32150–150063–400150–2500
डीएन40150–150063–400150–2500
डीएन50150–150063–400150–2500
DN65150–150063–400150–2500
डीएन80150–60063–400150–2500
डीएन100150–60063–400150–2500
DN125150–60063–400150–2500
डीएन150150–60063–400150–2500
डीएन200150–30063–400150–2500
डीएन250150–300——
DN300150——
Pressure Rating Options — Part 3 of 3
SizeClamp PN
DN410
DN610
DN1010
DN1510
DN2010
डीएन2510
DN3210
डीएन4010
डीएन5010
DN6510
डीएन8010
डीएन10010
DN125—
डीएन150—
डीएन200—
डीएन250—
DN300—

PN and Class are separate rating systems. Available ratings depend on the connection and size. Entries marked “—” are not specified here; confirm on request.

Selection Options

चयनकोडविकल्प
ElectronicsGAWithout local display
ElectronicsजीएनIntegral LCD
ConnectionF1Flanged
ConnectionF2Wafer
ConnectionF3Sanitary clamp
ConnectionL1External thread
ConnectionL2Internal thread
Body material4304 स्टेनलेस स्टील
Body material6316 stainless steel
Rotor material2C2Cr13 stainless steel
Rotor material252205 duplex stainless steel
आउटपुटGA124 V DC, no local display, 4–20 mA
आउटपुटGA224 V DC, no local display, pulse
आउटपुटGN124 V DC, local display, pulse
आउटपुटGN224 V DC, local display, 4–20 mA
आउटपुटGN324 V DC, local display, 4–20 mA + HART
आउटपुटGN424 V DC, local display, Modbus RTU over RS485
Temperature1−40 to +80°C
Temperature2−40 to +120°C
Temperature3−40 to +150°C
Hazardous-area requirementNNon-explosion-protected version
Hazardous-area requirementDFlameproof version; confirm marking and certification for the selected configuration

State the required nominal size, pressure rating, accuracy class, electrical connection and transmitter appearance when ordering. The final configuration must be confirmed for the application.

आयाम

Dimensions are in millimetres unless otherwise stated. Use the dimensional drawing and table for the selected connection and pressure rating.

External Thread Connection

ADDA-FL-WL turbine flow meter side-view dimensional drawing with threaded ends
External-thread connection, DN4–DN10, with straight pipe sections
ADDA-FL-WL threaded turbine flow meter side and end dimensions
External-thread connection, DN15–DN80

DN4–DN10 external-thread versions include straight pipe sections. DN15–DN80 versions do not include straight pipe sections.

Sizeदबाव रेटिंगएल (मिमी)G male threadb (mm)
DN4PN63 or lower296G1/213
DN6PN63 or lower296G1/213
DN10PN63 or lower413G1/213
DN15PN63 or lower75G115
DN20PN63 or lower85G115
डीएन25PN63 or lower100G1-1/415
DN32PN63 or lower140G220
डीएन40PN63 or lower140G220
डीएन50PN63 or lower150G2-1/230
DN65PN63 or lower170G335
डीएन80PN63 or lower200G440

Internal Thread Connection

ADDA-FL-WL flanged turbine flow meter side-view dimensional drawing
Internal-thread connection, DN4–DN50
Sizeदबाव रेटिंगएल (मिमी)G female threadडी (मिमी)
DN4PN63 or lower75G3/842
DN6PN63 or lower75G3/842
DN10PN63 or lower75G1/242
DN15PN63 or lower100G1/244
DN20PN63 or lower120G3/443
डीएन25PN63 or lower120G149
DN32PN63 or lower120G1-1/456
डीएन40PN63 or lower120G1-1/260
डीएन50PN63 or lower120G272

Flanged Connection

ADDA-FL-WL turbine flow meter side and end dimensional views
Small-bore flanged connection with straight pipe sections
ADDA-FL-WL flange bolt pattern and transmitter dimensional views
Flanged connection dimensions
PN flange dimensions — Part 1 of 2
Sizeदबाव रेटिंगएल (मिमी)डी (मिमी)
DN4PN40 or lower29695
DN6PN40 or lower29695
DN10PN40 or lower41395
DN15PN40 or lower7595
DN20PN40 or lower85105
डीएन25PN40 or lower100115
DN32PN40 or lower140140
डीएन40PN40 or lower140150
डीएन50PN40 or lower150165
DN65PN16170185
डीएन80PN16200200
डीएन100PN16220220
DN125PN16250250
डीएन150PN16300285
डीएन200PN16350340
डीएन250PN16400405
DN300PN16350460
PN flange dimensions — Part 2 of 2
SizeK (mm)d (mm)n holes
DN465144
DN665144
DN1065144
DN1565144
DN2075144
डीएन2585144
DN32100184
डीएन40110184
डीएन50125184
DN65145188
डीएन80160188
डीएन100180188
DN125210188
डीएन150240228
डीएन2002952212
डीएन2503552612
DN3004102612
Class 150 flange dimensions — Part 1 of 2
SizePressure classएल (मिमी)डी (मिमी)
DN4Class15029690
DN6Class15029690
DN10Class15041390
DN15Class1507590
DN20Class15085100
डीएन25Class150100110
DN32Class150140115
डीएन40Class150140125
डीएन50Class150150150
DN65Class150170180
डीएन80Class150200190
डीएन100Class150220230
DN125Class150250255
डीएन150Class150300280
डीएन200Class150350345
डीएन250Class150400405
DN300Class150350485
Class 150 flange dimensions — Part 2 of 2
SizeK (mm)d (mm)n holes
DN460.3164
DN660.3164
DN1060.3164
DN1560.3164
DN2069.9164
डीएन2579.4164
DN3288.9164
डीएन4098.4164
डीएन50120.7184
DN65139.7184
डीएन80152.4184
डीएन100190.5188
DN125215.9228
डीएन150241.3228
डीएन200298.5228
डीएन2503622612
DN300431.82612

Wafer Connection

ADDA-FL-WL flanged turbine flow meter side and front dimensions
Wafer connection dimensions
Sizeदबाव रेटिंगएल (मिमी)डी (मिमी)
DN15PN400 or lower6553
DN20PN400 or lower6053
डीएन25PN400 or lower6058
DN32PN400 or lower7066
डीएन40PN400 or lower7072
डीएन50PN400 or lower7092
DN65PN400 or lower80100
डीएन80PN400 or lower90112
डीएन100PN400 or lower100137
DN125PN400 or lower120165
डीएन150PN400 or lower150190
डीएन200PN400 or lower150242

The catalogue gives the same wafer body dimensions across the available pressure ratings. When supplied with mating weld-neck flanges, total length equals the standard body length plus twice the mating-flange thickness.

Sanitary Clamp Connection

ADDA-FL-WL compact turbine flow meter body and transmitter dimensions
Sanitary clamp connection dimensions
ADDA-FL-WL turbine flow meter transmitter and flange front view
Sanitary clamp connection end view
Sanitary Clamp Connection — Part 1 of 2
Sizeदबाव रेटिंगएल (मिमी)डी (मिमी)
DN4PN105050.5
DN6PN105050.5
DN10PN105050.5
DN15PN1010050.5
DN20PN1010050.5
डीएन25PN1010050.5
DN32PN1012050.5
डीएन40PN1014064
डीएन50PN1015077.5
DN65PN1017091
डीएन80PN10200106
डीएन100PN10220130
Sanitary Clamp Connection — Part 2 of 2
Sized (mm)सी (मिमी)
DN4443.5
DN6643.5
DN101043.5
DN151543.5
DN202043.5
डीएन252543.5
DN323243.5
डीएन404056.5
डीएन505070.5
DN656583.5
डीएन808097
डीएन100100122

Installation Requirements

RequirementGuidance
Straight pipe after reducers, expanders or elbowsProvide at least 15D upstream and 5D downstream. D is the nominal internal diameter of the flow meter.
Pipe alignmentAlign the meter and pipeline concentrically before installation.
CleanlinessFlush new pipework before fitting the meter to remove welding debris and other foreign material.
Process connectionsUse the mating fittings, gaskets, fasteners and sealing method appropriate to the selected thread, flange, wafer or clamp connection.

संबंधित उत्पाद

केस शोकेस

अक्सर पूछे जाने वाले प्रश्न

उत्पाद चयन, अनुकूलन, तकनीकी पैरामीटर, वितरण और ADDA औद्योगिक माप उपकरणों के समर्थन के बारे में त्वरित उत्तर खोजें।.

官网询盘

यदि दूरस्थ निगरानी की आवश्यकता है तो कृपया मापा माध्यम, मापने की सीमा, प्रक्रिया तापमान, प्रक्रिया दबाव, कनेक्शन प्रकार, आउटपुट सिग्नल, बिजली आपूर्ति, स्थापना वातावरण और संचार विधि प्रदान करें।.

हाँ। ADDA रेंज, प्रक्रिया कनेक्शन, गीली सामग्री, प्रदर्शन प्रकार, संचार प्रोटोकॉल, स्थापना विधि और कार्य वातावरण को मापने के आधार पर अनुकूलित समाधान प्रदान कर सकता है।.

कई एडीडीए उपकरण विस्फोट-सबूत या आंतरिक रूप से सुरक्षित कॉन्फ़िगरेशन के साथ उपलब्ध हैं कृपया चयन से पहले साइट वर्गीकरण और प्रमाणन आवश्यकताओं की पुष्टि करें।.

हाँ। हमारी टीम माध्यम, रेंज, कनेक्शन, आउटपुट सिग्नल और इंस्टॉलेशन आवश्यकताओं सहित आपकी एप्लिकेशन स्थितियों की समीक्षा करने के बाद एक उपयुक्त उपकरण कॉन्फ़िगरेशन की सिफारिश करने में मदद कर सकती है।.

लीड समय उत्पाद प्रकार, मात्रा, अनुकूलन आवश्यकताओं और प्रमाणन आवश्यकताओं पर निर्भर करता है मानक उत्पादों में आमतौर पर कम वितरण समय होता है, जबकि अनुकूलित मॉडल को अतिरिक्त उत्पादन समय की आवश्यकता हो सकती है।.

सहयोग के लिए हमसे संपर्क करें

官网询盘